box-sousmenu-top
box-sousmenu-bottom
Wi-Fi Router 

Router configuration 

Step 1: Open your Web browser and type in the router IP address (192.168.0.1 by default).

 

routeurdlinkvideotron1


Step 2: Enter the username (admin) and password (blank by default), and then click OK or Log in.

 

routeurdlinkvideotron2

 

Step 1: Make sure the computer you are using is connected to the router with an Ethernet cable.

 

Step 2: Click Start and select Run.

 

Step 3: In the Run command box, type cmd and click OK.

 

routeurdlinkvideotron3

 

Step 4: In the command prompt, type ipconfig and press Enter.


Step 5: Locate the Ethernet adapter Local Area Connection. Under this header, find the Default Gateway. The address displayed here should be the address of the router (192.168.0.1 by default).

 

To perform a reset, please follow steps below:

Step 1: With the unit on, insert a paper clip into the hole labelled Reset on the back of the unit.
 
Step 2: Hold the paper clip down for 10 seconds and release.

Note: Do not repower the unit during this procedure.

 

Step 3: The unit will reboot on its own. Once the WLAN light stops blinking, the unit is reset.

 

(NOTE: To reach the configuration page of your D-Link router in Mac OS, you will need a Java-compatible browser, such as Firefox or Camino.)

 

(NOTE: Some routers have a "Captcha" graphical login option. This option can be disabled in the advanced options of the router’s configuration.)

 

Step 1: Open a Web browser and enter the router’s IP address in the address bar (default is 192.168.0.1). Press Enter.

 

Step 2: The default username is admin and the password field is left blank. Click OK.

 

Step 3: Click the Tools tab and then click Admin on the left.

 

routeurdlinkvideotron5

 

Step 4: To change the administrative password, enter a new password in the Admin Password section.

 

Step 5: Click Save Settings to save the settings.

 

Step 1: Open a Web browser and type the router’s IP address in the address bar (default is 192.168.0.1). Press Enter.

 

Step 2: The default password is left blank. Click Log in.

 

Step 3: Click the Status tab at the top of the page to access the Device Info section.

Note: When you log in to your router, you will be directed to this page by default.

 

Step 4: The current firmware version is listed in the General section.

 

routeurdlinkvideotron6

 

This button is the Wi-Fi Protected Setup button. Wi-Fi Protected Setup (WPS) is a method of connecting to a wireless network that requires little configuration. WPS automatically configures a wireless network with a network name (SSID), WPA security key and authentication. WPS is designed to support Wi-Fi-certified 802.11 networks.
 

Unconfigured mode:
After setting up your wireless device with WPS and Push Button Configuration (PBC), simply press the WPS button on the side of the router. You will not have to create a wireless network name (SSID) or security key.

 

Note: When you use unconfigured mode, all router settings will be added automatically. There is no need to enable Wireless Network Settings.

However, you will not know the security key, which is required if you add another device that doesn’t use WPS.

 

Configured mode:
Both Wireless Network Settings and Wireless Security Mode must be configured, including the wireless security key. Click Save Settings and reboot.

 

routeurdlinkvideotron9

 

Note: After configuring the Wireless Network Settings, you will have to enter a personal identification number (PIN) generated from your wireless adapter in order to establish a proper connection between client and host.

routeurdlinkvideotron10 

 

routeurdlinkvideotron11

 

routeurdlinkvideotron12

 

Step 1: Log in to the router and click on the Advanced tab.

 

routeurdlinkvideotron10

 

Step 2: Click on WIFI-Protected Setup on the left.

 

Step 3: Click on Add Wireless Device Wizard at the bottom of the screen.

 

Step 4: Select Auto in configuration method. Click Next.

 

routeurdlinkvideotron11

 

Step 5: Select PIN and enter the PIN generated by the WPS-capable Wireless client. Click on Log in.

  
routeurdlinkvideotron12

 

Step 6: Start WPS on the wireless client device you are adding to your wireless network. As the router attempts to connect to the wireless client, the timer will be set.

 

A message will be displayed indicating that the wireless device has been successfully added, as shown below.

 

Yes, a USB hub can be added to the USB SharePort on the router to increase the number of USB devices shared with SharePort.

 

The D-Link® Xtreme N™ Dual Band Gigabit Router uses dual band technology to support both 2.4GHz and 5GHz wireless signals at the same time. This allows you to check email and browse the Internet using the 2.4GHz band, while simultaneously streaming high-definition (HD) movies and other media on the 5GHz band.
Dual band routers are designed for users seeking a true HD wireless connection that can handle multiple HD video streams throughout the house, while being backward-compatible with existing 802.11g and 802.11a products.

 

Step 1: Open your Web browser and type in the router IP address (192.168.0.1 by default).

 

routeurdlinkvideotron1

 

Step 2: Enter the User Name (admin) and password (blank by default), and then click OK or Log in.

 

routeurdlinkvideotron2

 

Step 3: Click the Advance tab and Website Filter on the left hand side of the screen. Select the option “Deny computers access to ONLY these sites” under Configure Website Filter. Indicate the Websites you wish to block or restrict access to. When you have finished, click Save Settings.

 

routeurdlinkvideotron13

 

Step 4: Next, click the Access Control Tab and check the Enable Access Control box. You will then have to set up a policy for the Website filter. Click Add Policy and follow the wizard.

 

routeurdlinkvideotron14

 

Step 5: Click Next.

 

routeurdlinkvideotron15

 

Step 6: Name the policy and click Next.

 

routeurdlinkvideotron16

 

Step 7: Select a Schedule and click Next.

 

routeurdlinkvideotron17

 

Step 8: Select the IP or MAC addresses of the machine(s) the policy applies to and click Next.

 

routeurdlinkvideotron18

 

Step 9: Select Filtering Method and click Next.

 

routeurdlinkvideotron19

 

Step 10: Enable or disable Web Access Logging and click Next.

 

routeurdlinkvideotron20

 

Step 11: You should now see the policy listed at the bottom under Policy Table. Click Save Settings.

 
routeurdlinkvideotron21

 

Has this article answered your questions?
YES
No